Jurnal Elektro dan Mesin Terapan
1. Paper Title
This is your opportunity to attract the reader’s attention. Remember that readers are the potential authors who will cite your article. Identify the main issue of the paper. Begin with the subject of the paper. The title should be accurate, unambiguous, specific, and complete. Do not contain infrequently-used abbreviations.
The title of the paper should be in 18 pt Font Times New Roman and be centered. The title should have 0 pts space above and 12 pts below.
2. Authors Name, Affiliations, and Mailing Address
Write Author(s) names without a title and professional positions such as Prof, Dr, Production Manager, etc. Do not abbreviate your last/family name. Always give your First and Last names. Write clear affiliation of all Authors. Affiliation includes a name of department/unit, (faculty), a name of university. Please indicate Corresponding Author (include email address) by adding an asterisk (*) in superscript behind the name.
Author names should be in 10 pt Times New Roman with 0 pts above and 12 pts below. Author addresses are superscripted by numerals and centered over both columns of manuscripts. Author affiliations University name / institution / research study / company should be in 9 pt Times New Roman. Author mailing address should be in 9 pt Times New Roman.
The word “Abstract” should put in center, bold, 11 point, paragraf space after 10 poin. Abstract should contain summary of the all research (aim, scope, result and conclusion) with 150-200 words, justified, 11 point, and line spacing : single. For keywords wrote in italic and then separated using symbol (,) with maximum are 3 words.
In Introduction, Authors should state the objectives of the work at the end of introduction section. Before the objective, Authors should provide an adequate background, and very short literature survey in order to record the existing solutions/method, to show which is the best of previous researches, to show the main limitation of the previous researches, to show what do you hope to achieve (to solve the limitation), and to show the scientific merit or novelties of the paper. Avoid a detailed literature survey or a summary of the results.
To prepare your paper, use directly this template and simply replace this text by your text. These instructions are to be followed strictly, and it is strongly advised to use the styles indicated in this document between square brackets. It is strongly advised NOT to use formatting or styles in your paper different from the ones mentioned here.
The text should be in 11 pt Times New Roman. The structure of manuscripts should follow the following order; title, authors, affiliations, abstract, keywords, main text, references. The items with parentheses are not mandatory.
5. Section Headings
The way chapter titles and other headings are displayed in these instructions is meant to be followed in your manuscript.
Level 1: Times New Roman, 11, Bold, 10 pt spacing before heading, 5 pt spacing after heading.
Successive Levels: Times New Roman, 8, Bold, 6 pt spacing before heading, NO spacing below the heading.
Do NOT begin a new section directly at the bottom of the page, but transfer the heading to the top of the next page. Cite the main scientific publications on which your work is based. Cite only items that you have read. Do not inflate the manuscript with too many references. Avoid excessive self‐citations. Avoid excessive citations of publications from the same region. Check each reference against the original source (authors name, volume, issue, year, DOI Number).
6. Symbols and units, numbers
If symbols are defined in a nomenclature section, symbols and units should be listed in alphabetical order with their definition and dimensions in SI units. Please use the SI set of units as much as possible. Wherever the application domain uses a different set of units widely, please minimize the use of non-standard units or non-standard symbols for those units. As examples, the use of “a” for the year (annum) is depreciated and the use of “y” is encouraged instead. Similarly, “h” should be used for hours instead of “hr” and “t” instead of “ton” or “tonne”. It is important to take care of the case in which the measurement units are typed. E.g. “Km” does not mean “kilometers”, but “Kelvin-meters”.
When providing numerical values followed by measurement units, please leave a regular space or non-breaking space between each value and the measurement unit. This also includes percentages and degrees Celsius (e.g. 42 % or 35 %, 234 °C, 504 K). This rule also applies to the unit for a litre, which is recommended to be capital “L”. The authors are encouraged to render the numbers according to the International rules, specifying the dot as a decimal separator and the comma as a thousand separator.
Make sure that placing and numbering of equations are consistent throughout your manuscript.
Left aligns the equation and put the number of the equation flush-right, using a Right Tab on the right margin. Please reference equations in the text by writing: Eqn. .. (do not use Equation ..) In principle, variables are to be presented in italics.
8. Figures and Tables
Figures and tables should be originals or sharp prints. Please use the SI set of units as much as possible. Figures and tables should be centered and placed either at the top or at the bottom of the page. Please do not render tables as pictures and please do not use too small font sizes in the illustrations. Please use the following fonts in your illustrations: Times New Roman, Symbol, or use fonts that look similar.
If your figures and tables are created in a Microsoft Office application (Word, PowerPoint, Excel) then please supply 'as is' in the native format, too. Regardless of the application used other than Microsoft Office, when your electronic artwork is finalized, please 'Save as' or convert the images to one of the following formats (note the resolution requirements for line drawings, halftones, and line/halftone combinations given below):
- EPS (or PDF): Vector drawings, embed all used fonts.
- TIFF (or JPEG): Color or grayscale photographs (halftones), keep to a minimum of 300 dpi.
- TIFF (or JPEG): Bitmapped (pure black & white pixels) line drawings, keep to a minimum of 1000 dpi.
- TIFF (or JPEG): Combinations bitmapped line/half-tone (color or grayscale), keep to a minimum of 500 dpi.
Set table number and title flush left above table. Horizontal lines should be placed above and below table headings and at the bottom of the table. Vertical lines should be avoided. The title should use Times New Roman 9, bold, with 6 pt before and 6 pt after the paragraph, left-justified at the top of the table. Tables have to be included in the text. If a table is too long to fit one page, the table number and heading should be repeated on the next page before the table is continued. Alternatively the table may be spread over two consecutive pages (first an even numbered, then an odd-numbered page) turned by 90, without repeating the heading.
10. Figure captions
Fig. 1 Captions should be placed below each illustration, font Times New Roman, 9 pts, bold. Figures and figure captions should be placed center; two narrow figures may be placed side-by-side. Please reference figures in the text by writing: Fig. .. (do not use Figure ..).
To write a bibliography, use the format as follows. The bibliography format follows the IEEE format using square brackets.
 Gupta, B.R. and Thapar B, "Title Paper", Journal Name, 1652-1660, 1980. (journal)
 Tobing, L. Bonggas, "Book Title", Publisher, edition, 2003. (book)
 Williams, J., Title Paper, in Proceedings. Names, editors (ed (s)), pp. 5-10, 2004. (Conference Proceedings)
 Author's name, Title of Paper (if available), Organization, URL link, (date of year). (Internet sources)
 Rashid, L., Thesis / Dissertation Title, Master Thesis, Name of Department, Name of College, City, 1997. (Thesis or Dissertation)